IBU.data
  • PUBLIC
  • REFERENCE_DATA
Data stock: PUBLIC

Process data set overview page

Data set: 1 m2 Alpha Sectional door ALU 60 (00.03.000)

Other versions:   00.02.000   00.01.000
Full name
1 m2 Alpha Sectional door ALU 60
Location
NL
Reference year
2017
Valid until
2022
Reference flow(s)
Type
EPD
Parameterized?
no
LCIA results included?
yes
Category
02 Building products / Doors, windows, shutters, and related products / Windows and doors
Synonyms
Use advice for data set
Scope: This Environmental Product Declaration (EPD) is valid for Alpha sectional doors of the type ALU 60. The production facilities are located in Didam (NL). The life cycle assessment is representative for the products introduced in the declaration for the given system boundaries. System boundary: Type of the EPD: cradle-to-gate. The production of the materials (steel, plastics, aluminiums, coating etc.) and also the motor-parts and other electronic components are modelled in A1. The transportation (road and sea) from the suppliers to Alpha deuren is modelled in A2. The assembly of the doors (energy use) and the packaging (including the production and transportation of the packaging materials) is modelled in A3. The generation of electricity and heat is modelled in A3. For the option coating is also the coatingprocesses and the emissions of non-methane volatile organic compounds to air modelled in A3. Production waste from A3 is modelled following the Dutch defaults for waste scenario’s (see 4.1.3). This modelling results in components for reuse, materials for recycling. According to EN 15804 (CEN 2013) the end-of-life system boundary of the construction product system is set where outputs of the system under study, e.g. materials, products or construction elements, have reached the end-of-waste state. Therefore, waste processing of the material flows (e.g. undergoing recovery or recycling processes) during any module of the product system (e.g. during the production stage, use stage or end-of-life stage) are included up to the system boundary of the respective module. For all phases A1-A3 also processing up to the end-of-waste state or disposal of final residues not leaving the factory gate with the product, are included.
Data set use approval
General comment
Sectional doors, type ALU 60, constructed from extruded aluminium sections with thermal separation fitted with 40 mm PMMA (polymethyl methacrylate) triple glazing. The panels are 60 mm thick and available in heights varying between 366 and 732 mm. The horizontal seal retaining profile on the top section is made from aluminium, or supplied with a spray painted finish (optional). The ALU sections can be combined with insulated, steel-skinned ISO panels. Surface treatment The panels are supplied as standard with an anodised finish. They can also be painted in a RAL colour chosen by the customer. This option is covered in the EPD for Sectional door ALU 60 with coating. Track systems are made of 1.7 mm thick, closed steel angle profiles fitted with roller tracks made of 1.7 mm thick galvanised steel. The door hardware is attached using electrolytically galvanised self-tapping screws with a knurled integral lock-washer. The rollers feature nylon wheels and an 11 mm galvanised steel shaft. The door leaf is balanced via torsion springs and hung on steel cables with a safety factor of 6. Manually operated doors are supplied with a plastic handle and foot plate in the bottom section and a steel shoot bolt, or an optional cylinder lock. Draft seals are fitted around the periphery of the door leaf: top, side and floor seals made from EPDM (ethylene propylene diene monomer rubber) seals between the panels made from EPDMOperators The industrial sectional door can be operated manually by pull cord or chain hoist, or supplied with an electric drive. This option is covered in the EPD for Sectional door ALU 60 with electric drive. Safety emergency chain hoist and emergency drive disconnect up to operator height in the case of electric drives cable break safety and/or slack cable safety spring break safety lift-up prevention Wicket doors The industrial sectional door can be supplied with an integral wicket door or a pass door next to the sectional door. This option is covered in the EPD for Sectional door ALU 60 with wicket door.
LCI Method Principle
LCI Method Approaches
No records found.
Completeness of product model
No statement
Reviews
  • Accredited third party review by
License and access conditions
Copyright
yes
Owner of data set
Novoferm Nederland B.V.
Technical purpose
Alpha industrial sectional doors are used in private homes, agricultural buildings, industrial buildings and non-residential buildings. For the application and use the respective national provisions apply. The space-saving industrial sectional door can be fitted to both outdoor and indoor walls. The ALU 60 sectional door is assembled from aluminium panels with a working height of between 366 and 732 mm. When the door is opened, the sections slide back under the roof. The weight of the door leaf is balanced using torsion springs to allow manual operation. In addition to the standard lift track system, high lift, vertical lift, roof following and low headroom systems are available. The industrial sectional door complies with /EN13241-1/ (products without smoke control and fire resistant characteristics)
Input Products
No records found.
Co-Products
No records found.
Data set version
00.03.000
Time stamp (last saved)
2017-09-25T10:44:01.455
Data set format
ILCD Format 1.1
Other versions
Compliance systems
  • DIN EN 15804 (Overall compliance: Not defined)
  • ISO 14025 (Overall compliance: Not defined)
Data Set deregistration
Are you sure you want to deregister selected dataset?
Please enter the reason of deregistration and confirm.